How to Install a Ghost Immobiliser
A ghost immobiliser guards your vehicle from key cloning and hacking. It works by preventing the engine of your vehicle from starting unless it is started using a PIN code, which can be up to 20 characters long.
This additional layer of security is not detectable by thieves who might not be expecting it. Some systems also have an application that lets owners disable the immobiliser in the event that they forget their PIN, or to use the service/valet mode.
Connecting the vehicle's CAN Bus to the vehicle's
The Ghost 2 Immobiliser is an innovative security system that is able to be integrated into your vehicle's ECU, providing a discreet security line against thieves. It is highly efficient and user-friendly. This makes it a valuable asset to your vehicle's security arsenal. But, as with any other anti-theft device, it is not 100% reliable and requires regular maintenance to ensure proper operation. This guide will help you get the most of your Ghost 2 immobiliser.
CAN (Controller Area Network) is a reliable serial network that allows microcontrollers to communicate with one another across short distances without the need for central control units. It is designed to multiplex electrical wiring in vehicles, which saves on copper. It has numerous advantages, such as low cost and easy use.
The CAN protocol is used in most modern cars to communicate with the engine management system, transmission controller, steering control module and air conditioning controls and more. It also transmits sensor data, such as speed sensors and other inputs, to regulate the vehicle's various features. The CAN bus is able to monitor the condition of these different components and can stop the vehicle from starting if it's in a dangerous condition.
While the CAN bus can be used for a variety of reasons, it's essential to understand how it works and how it's secured. It's possible to add new features to a vehicle by using CAN bus, however it's important to secure it against hackers and other threats. The best method to achieve this is to install firewalls and monitoring your CAN bus through software.
Ghost2's discrete control unit is hidden inside the dashboard of the car or in the wiring harness, preventing a thief from physically tampering it. It is also impossible to reset a PIN code or an emergency code without access to the car.
You can enable Transport Mode when you have to sell your car for service, valet parking or any other reason. This feature disables both the keyfob and the ignition functions of the Ghost immobiliser. It will only be activated after the car has reached 31 mph for a period of 15 minutes.
How to create a PIN code
The Ghost immobiliser is an effective security system that guards your vehicle from thieves. The revolutionary technology utilizes a PIN to disable the engine of the vehicle and stop it from starting if you don't have the correct code, or a valid fob or mobile. The system's subtle design ensures the system is inconspicuous and offers unbeatable security against theft. The system is TASSA-verified and can save you significant sums on your car insurance.
During the installation, Ghost enters a "learning mode" to record the sequence of buttons that are that are pressed to generate your unique pin codes. Once the pin code is created and the installer has completed its work, it will guide you through the process of activating the system. Once activated by the system, the Ghost system will turn off your vehicle's starter motor until a valid PIN has been entered or the vehicle is switched into transport mode. This makes it very difficult for thieves or cloners to hack into or replicate your starter system.
It is simple to install a Ghost immobiliser, however, you must follow the detailed instructions included in the user's guide to ensure that it is operating properly. Multimeters and basic hand tools can be used to check electrical values. Insulation tape as well as heat shrink tubing and cable ties can be utilized to shield exposed wiring. Be sure to test the system on a regular basis to find any problems and potential errors.
Once More Material is complete, it is important to perform a final check of the system before switching on the ignition of your vehicle. Ghost immobilisers will re-arm themselves after 3 to 30 second dependent on the model of the vehicle. It also has the option of a Service/Valet mode, which allows you to temporarily disable the system while you are servicing your vehicle or parking valet.
Ideally, the immobiliser should be placed in an inconspicuous location under the steering wheel or dashboard. Use a small piece duct tape or paint on the CAN H and L wires to make them easier to locate when you are testing. In addition, the CAN H and L wires should be connected to a source of power that is able to provide continuous 12V. It is also crucial to check the connections again after testing, since misidentifying these wires can cause the system to fail.
Invoking the system
A ghost immobiliser blocks your car from starting when you press certain buttons inside the vehicle, typically on the steering wheel or the door panel, or the central console. The sequence can be changed by the user if needed. Once the system is activated it cannot be deactivated by thieves and is a great option for anyone who wishes to protect their vehicle from theft.
The system is designed not to be detected by modern diagnostic and code-grabbing technologies. It also doesn't broadcast out radio frequencies, which makes it even harder for thieves to detect the device.
If the device is detected, it will stop the engine from starting and will sound an alarm with a loud sound to scare away the thief. The device can be used to monitor the location of the car, which can help police track it down in the event of theft.
Contact Car Specalist Customs for a estimate or to discuss your options if you're interested in Ghost immobiliser. We are certified to install ghost immobilisers on your vehicle. We will ensure that it is concealed in a place that is difficult to reach. We can also provide other security measures like a wheel lock and kill switch to keep your car safe from thieves.
Disarming the System
If you have a Ghost immobiliser that is fitted to your vehicle, it's important to know how you can disable it. It can be used in the event you forget your keys or your car battery fails. The system utilizes a unique PIN code that only you know. It won't be able to start the vehicle without this code. The most efficient method of entering the code is to press a set of buttons on your dashboard or the steering wheel. This is much simpler than using a key fob. It also stops others from copying your remote.
In contrast to some aftermarket immobilisers that require cutting wires for installation, Ghost2 is non-invasive and works with your vehicle's CAN bus network to function. Its standout feature is its ability bypass the engine without affecting the normal functions, making it hard for thieves to use signal boosters to clone your car key. Moreover, it does not emit radio frequencies, so thieves won't be able to detect it.
The Ghost system also features a Transport Mode that allows you to temporarily disable the security system for occasions like transportation or servicing. This feature is useful for when you're loaning your vehicle out to someone else, without sharing your PIN number, or if your vehicle needs to be secured even while you drive it. To activate Transport Mode, press the service button five times within 2 seconds. The Ghost system will confirm activation using 5 indication signals.
When you're done, remember to save the emergency code in a safe place outside of your vehicle. If you ever find yourself locked out of your car, you can call the technician or company who installed the system, and they'll give you the code. If you are unable to reach them, then you can seek out an authorized dealer. However, this may involve verification procedures, and you may be charged additional charges.
This system isn't just practical, but it can also safeguard your vehicle from theft, and also reduce insurance costs. Many insurance companies offer reduced costs or financial incentives for those who install this anti-theft system.